For sale Technics su-ma 10 made for the Japanese market and sold under the Panasonic name
100 volt alternating current.
Digital straight amplifier with twin monaural configuration using D. D. D. D.
Uses D. D. D. (Digital Direct Drive) system.
In this method, unlike conventional amplifiers with only a DAC mounted on them, the output signal of the DAC is increased to the voltage of the required sound level, and it is directly connected to a power amplifier with an amplification degree of 1 (0 dB) without going through the amplification path of the analog source. As a result, the output voltage of the DAC part is equal to the voltage of the speaker terminal, and excellent transmission characteristics are achieved.
In addition, in order to operate the 0 db power amplifier stably, it uses a combination of Technics original classAA and floating power supply to realize an S/N ratio of 140 db in the power amplifier section.
The D. D. D. cannot perform normal volume control, so a high voltage I/V converter is mounted on the DAC output as a voltage variable means. By changing the conversion ratio, the output voltage can be varied to adjust the volume.
MASH1-bit DAC is used for the D/A conversion part.
Mash reduces re-quantization noise in the audible frequency band by over-sampling 16-bit input data with a digital filter and then noise-shaping it. In addition, the PWM method, which in principle does not generate non-linear distortion such as 0 cross distortion, enables D/A conversion with extremely high accuracy, and enhances the reproduction capability of small signals, which tend to be buried in distortion components of high-level signals.
In order to reduce the jitter distortion in the digital transmission path, which is a problem in the amplifier with built-in DAC, a unique digital interface receiver is installed. This circuit reduces the jitter distortion by adopting the VCXO method using quartz with extremely high oscillation accuracy.
It is also equipped with a 2-PLL system with two VCoS to provide a 2-mode / 2-PLL system. The VCXO system is automatically selected for sources with high oscillation precision such as CD players, and the 2-PLL system is automatically selected for sources with low oscillation precision.
The power supply section is equipped with a 300 VA high-capacity transformer independently on the left and right sides. This transformer is used with a magnetic flux density approximately 30% lower than usual, minimizing mechanical vibration and magnetic radiation.
A newly developed X-Pro twin capacitor is used for the electrolytic capacitor. Two electrolytic capacitors for the positive and negative power supply are enclosed in a resin case with a copper cap. The capacitor is filled with vibration absorbing material to reduce mechanical vibration and electromagnetic radiation.
The power amplifier section has a twin monaural configuration in which the left and right sides are independent. In addition, the preamplifier section and digital section have a T-shaped configuration with a tight shield. This minimizes interference between the left and right channels caused by electromagnetic waves from the large current of the power amplifier section, and prevents noise from entering the final 0 db amplifier.
In addition to digital inputs of two optical and two coaxial systems, four analog inputs are installed.
Type Digital straight amplifier
Power Amplifier Unit
Effective power 100W + 100W (6 Ω, 20 Hz to 20 kHz, T. H. D 0.007%)
Total harmonic distortion factor 0.003% (20 Hz to 20 kHz -3dB, 8 Ω)
Damping factor 110 (8 Ω)
55 (4 Ω)
Preamplifier Section
Frequency characteristic Tuner, aux1/2, tape, DAT : 0.8 Hz to 120 kHz + 0 to 3 dB
20 Hz ~ 20 kHz + 0 -0.2 dB
Input Sensitivity / Impedance Tuner, aux1, tape, DAT : 150mV/100k Ω
aux2 : 150mV/22k Ω
Signal-to-noise ratio Tuner, aux1/2, tape, DAT : 105 dB (IHF' 66)
Digital Part
Total harmonic distortion factor 0.005% or less (EIAJ)
Frequency characteristic 2 Hz to 20 kHz ± 0.3 dB
some inscriptions on the front are worn out
signs of use are visible, minor scratches
Pwer 100 VAC, 50Hz/60Hz
Power consumption 250W
External dimensions Width 430x Height 186x Depth 433 mm
Weight 25.0kg
rarely available
Beautiful and powerful Sound optical input
requires converter, min. 700 W
preamp input also available, which is not found on the European version
sent in carefully wrapped foam packaging
Just shipping in Europa!
采用数字直驱(D. D. D.)系统。 在这种方法中,与传统的仅配备DAC的放大器不同,DAC的输出信号被放大到所需音量的电压,并直接连接到增益为1(0 dB)的功率放大器,而不经过模拟信号源的放大路径。因此,DAC部分的输出电压等于扬声器端子的电压,实现了优良的传输特性。 此外,为了稳定操作0 dB功率放大器,它采用Technics原装的Class AA和浮动电源相结合,在功率放大器部分实现140 dB的信噪比。 D. D. D.无法进行正常的音量控制,因此在DAC输出端安装了高压I/V转换器,作为电压可调的方法。通过改变转换比,可以调节输出电压以调整音量。