No. 94793904

Sold
McIntosh - C8-S and C8 - 2 Mono tube preamplifiers Preamplifier - Multiple models
Final bid
€ 551
12 weeks ago

McIntosh - C8-S and C8 - 2 Mono tube preamplifiers Preamplifier - Multiple models

McIntosh : Paire de préamplificateurs mono à tubes C8 S et C8 (vintage) Pour connaisseurs, collectionneurs et puristes de la marque de prestige! Achetés aux Etats-Unis! Modèles très rares datant des années cinquante. Entièrement d'origine, aucune modification 2 préamplificateurs, (photos 16 à 85) 1 coffret bois, (photos 86 à 98) 1 cordon à fiches octales, (photos 99 à 104) Préamplificateurs mono qui doivent être alimentés par un amplificateur mono McIntosh à tubes ou par un amplificateur stéréo DYNACO ST-70 ou une alimentation séparée D 8 ou D 8A, (photo 104), schémas de connexion , (photo 105). Fonctionnement des préamplificateurs : Il faut deux cordons. Un cordon d'alimentation qui rentre dans le mur, (110 ou 220 volts). Et un autre (cordon ombilical) qui a des fiches octales à chaque extrémité. Le cordon d’alimentation : • Il fournit le courant alternatif aux prises commutées situées à l'arrière du préampli. L’ampli peut utiliser l’une de ces prises car il ne possède pas d’interrupteur d’alimentation propre. • Il allume également le voyant rouge « on ». • C'est à peu près tout ce que fait le cordon d'alimentation du préampli. Il n’alimente pas les circuits du préampli. Le cordon « ombilical »: • Il alimente les trois tubes et circuits audio du préampli à partir du transformateur de puissance de l'amplificateur. Cela inclut les filaments/cathodes des tubes, ainsi que le courant continu vers les circuits audio (le préampli possède son propre redresseur au sélénium à cet effet, mais il est d'usage de le remplacer par un type de diode au silicium pour des raisons de sécurité.) Modèle C8S: Permet de contrôler le signal stéréo ! (photos 16 à 53) Descriptifs précis du préamplificateur C8S : Mono avec commandes de volume et de balance stéréo Possède un redresseur interne à semi-conducteurs pour les filaments DC. Réponse 20-20 kHz. Distorsion 0,3%. Bruit et bourdonnement -80dB haut niveau, phono 2uV Sortie nominale 2,5 V Sensibilité et impédance d'entrée : haut niveau 0,5 V à 500 k, phono 1 5 mV à 100 k, phono 2 variable 6,8 k à 52 k PANNEAU AVANT : Filtre Rumble : 1 à 5. Compensateur sonore : 1 à 5. Compensateur d'enregistrement : turnover (graves) 950, 750, 580, 400, 280, rolloff (aigus) 5, 10, 15, 20, 25 Sélecteur : bande, tuner, tête de bande, phono 1, phono 2 Tonalité : basses et aigus concentriques Mode : tour, stéréo, norme, l, r, mon. Équilibre Volume avec interrupteur d'alimentation Voyant d'alimentation. PANNEAU ARRIÈRE : Entrées : bande, tuner, tête de bande, phono 1, phono 2 Contrôles de niveau d'entrée pour chaque entrée Contrôle de charge phono Sorties : principale et bande Prises stéréo : entrée et sortie laissées Prise d'alimentation et de sortie Prises secteur : 3 commutées. TUBES : 3 tubes 12AX 7 ou similaires non testés Vendu de 1958 à 1960 Dimensions du préamplificateur : Largeur : 28 cm, profondeur : 20 cm, hauteur : 11 cm En très bon état de conservation La façade en laiton massif est superbe Tous les boutons s'articulent correctement Modèle C8: A associer avec le modèle C8S, (photos 54 à 85) Descriptif précis : Le Compensateur Audio McIntosh est une unité de contrôle complète pour les systèmes de divertissement professionnels ou à domicile. Réponse en fréquence : 20 Hz à 20 kHz Distorsion harmonique totale : 0,3% Sensibilité d'entrée : 5 mV (MM), 500 mV (ligne) Rapport signal/bruit : 80 dB (ligne) Sortie : 500 mV (ligne), 2,5 V (pré-sortie) TUBES : non présents Vendu en 1955 Dimensions du préamplificateur : Largeur : 28 cm, profondeur : 20 cm, hauteur : 11 cm En très bon état de conservation La façade en laiton massif est superbe Tous les boutons s'articulent correctement "APPAREILS NON TESTES » qui nécessitent une remise en état pour une utilisation normale" Ces préamplificateurs seront parfaitement emballés et protégés dans un colis sur mesure pour une expédition en France ou en Europe en toute sécurité. Photos des étapes de l’emballage envoyées à l’acheteur(teuse) BONNES ENCHERES A TOUS(TOUTES)…

No. 94793904

Sold
McIntosh - C8-S and C8 - 2 Mono tube preamplifiers Preamplifier - Multiple models

McIntosh - C8-S and C8 - 2 Mono tube preamplifiers Preamplifier - Multiple models

McIntosh: Pair of vintage mono tube preamplifiers C8 S and C8

For connoisseurs, collectors and purists of the prestigious brand!

Purchased in the USA!

Very rare models from the 1950s.

Completely original, no modifications

2 preamplifiers, (photos 16 to 85)
1 wooden box, (photos 86 to 98)
1 octal plug cord (photos 99 to 104)

Mono preamplifiers that must be powered by a McIntosh tube mono amplifier or a DYNACO ST-70 stereo amplifier or a separate D 8 or D 8A power supply, (photo 104), connection diagrams, (photo 105).

Operation of preamplifiers:
It takes two cords. A power cord that plugs into the wall (110 or 220 volts). And another (umbilical cord) that has octal plugs at each end. The power cord: • It supplies AC power to the switched outlets located at the back of the preamp. The amplifier can use one of these outlets because it does not have its own power switch. • It also lights up the red "on" indicator. • That's about all the power cord does for the preamp. It does not power the preamp's circuits. The "umbilical" cord: • It powers the three tubes and audio circuits of the preamp from the power transformer of the amplifier. This includes the filaments/cathodes of the tubes, as well as the DC current to the audio circuits (the preamp has its own selenium rectifier for this purpose, but it is common practice to replace it with a silicon diode type for safety reasons.)

Model C8S: Allows you to control the stereo signal! (photos 16 to 53)

Detailed descriptions of the C8S preamplifier:
Mono with volume and stereo balance controls
Has an internal semiconductor rectifier for DC filaments.
Response 20-20 kHz.
Distortion 0.3%.
Noise and humming -80dB high level, phono 2uV
Nominal output 2.5 V Input sensitivity and impedance: high level 0.5 V at 500 k, phono 1 5 mV at 100 k, phono 2 variable 6.8 k to 52 k.
FRONT PANEL: Rumble Filter: 1 to 5.
Sound compensator: 1 to 5.
Registration compensator: turnover (low) 950, 750, 580, 400, 280, rolloff (high) 5, 10, 15, 20, 25
Selector: tape, tuner, tape head, phono 1, phono 2
Tone: concentric bass and treble Mode: tour, stereo, norm, l, r, mono.
Volume balance with power switch Power indicator.
BACK PANEL: Inputs: tape, tuner, tape head, phono 1, phono 2
Entry level checks for each input
Phono load control
Outputs: main and band Stereo jacks: left input and output
Power input and output
Power outlets: 3 switched.
TUBES: 3 tubes 12AX7 or similar untested
Sold from 1958 to 1960
Dimensions of the preamplifier: Width: 28 cm, depth: 20 cm, height: 11 cm

In very good condition
The solid brass front is superb
All the buttons move correctly.

Model C8: To be paired with model C8S, (photos 54 to 85)

Precise description:
The McIntosh Audio Compensator is a complete control unit for professional or home entertainment systems.
Frequency response: 20 Hz to 20 kHz
Total harmonic distortion: 0.3%
Input sensitivity: 5 mV (MM), 500 mV (line)
Signal-to-noise ratio: 80 dB (line)
Output: 500 mV (line), 2.5 V (pre-output)
TUBES: not present
Sold in 1955
Dimensions of the preamplifier: Width: 28 cm, depth: 20 cm, height: 11 cm

In very good condition
The solid brass front is superb
All the buttons move correctly.


"UNTREATED DEVICES" that require refurbishment for normal use


These preamplifiers will be perfectly packed and protected in a custom-made package for safe shipping to France or Europe.

Photos of the packaging stages sent to the buyer

HAPPY BIDDING TO ALL...

You might also like

Set a search alert
Set a search alert to get notified when new matches are available.

This object was featured in

                                        
                                                                                                    
                    
                                        
                                                                                                    
                    
                                        
                                                                                                    
                    
                                        
                                                                                                    
                    

How to buy on Catawiki

Learn more about our Buyer Protection

      1. Discover something special

      Browse through thousands of special objects selected by experts. View the photos, details and estimated value of each special object. 

      2. Place the top bid

      Find something you love and place the top bid. You can follow the auction to the end or let our system do the bidding for you. All you have to do is set a bid for the maximum amount you want to pay. 

      3. Make a secure payment

      Pay for your special object and we’ll keep your payment secure until it arrives safe and sound. We use a trusted payment system to handle all transactions. 

Have something similar to sell?

Whether you're new to online auctions or sell professionally, we can help you earn more for your special objects.

Sell your object